beneteau 36 sailboat data

• AROUND THE SAILING WORLD
• BOAT OF THE YEAR
• Email Newsletters
• Best Marine Electronics & Technology
• America’s Cup
• St. Petersburg
• Caribbean Championship
• Boating Safety

Beneteau First 36, Sailing World 2023 Boat of the Year

• By Dave Reed
• December 16, 2022

Sailing World Magazine’s  annual Boat of the Year tests are conducted in Annapolis, Maryland, following the US Sailboat Show. With independent judges exhaustively inspecting the boats on land and putting them through their paces on the water, this year’s fleet of new performance-sailing boats spanned from small dinghies to high-tech bluewater catamarans. Here’s the best of the best from our  2023 Boat of the Year nominees »

The Total Package

• Beneteau First 36 2023 Boat of the Year
• Stated purpose: Shorthanded racing, club racing, coastal cruising
• Crew: Solo to six
• Praise for: Build quality, deck layout, versatility
• Est. price as sailed: $345,000

Like a runaway, the Beneteau First 36 careens across a westerly-whipped Chesapeake Bay. The boat’s big-shouldered spinnaker and mainsail are silhouetted in the early October morning light. It’s making trees on the Eastern Shore as we peg the throttle down to keep chase in a 19-foot RIB. The four crewmembers on board are having a casual conversation—like no big deal—when a cold and meaty gust fills the spinnaker. The leech flickers, and the boat surges forward onto plane. Twin rudders zipper the slick streaming out from the transom as the helmsman, hands at 10 and 2 on the carbon steering wheel, effortlessly weaves the boat across waves tops. The boat is, as the saying goes, on rails.

“Wicked,” is how senior Boat of the Year judge Chuck Allen summarizes his experience when he steps off. “That boat is going to be hard to beat.”

Three days and 10 boats later, nothing comes close to usurping the Beneteau First 36 as the obvious and unanimous Boat of the Year, a boat that has been a long time coming and overdue. It’s a boat that will serve many masters.

Beneteau initiated its First 36 project in 2019 by surveying a broad focus group of First “Point 7” owners and dealers about what they wanted in the marketplace, and the takeaways were: 1) Not another ­displacement boat—it had to plane. 2) They wanted a lounge, not a dining room. 3) They wanted their nav station back, and 4) for that, they were OK with having a smaller head.

Given the boat was to meet all three of its club racing, shorthanded and cruising demands, the brain trust assembled inside and outside of Beneteau focused on No. 1—keeping it light and fast. Naval architect Samuel Manuard, the new hot talent of the IMOCA 60 and Class 40 scenes, did the hull, keel and rig. Pure Structural Engineering took care of the structure, and the weight-obsessed glass slingers at Seascape’s factory in Slovenia ensured the boat came in at not a pound more than 10,580. At that weight, of course it’s going to plane.

The entire boat is ­vacuum-infused with CoreCell (hull) and PVC (bulkheads) from the deck down, inside and out, and everything, except the fridge, is somehow a piece of the structure puzzle.

“We are saving big weight there, as furniture is also part of the structure, and all of it glued together makes the boat extremely stiff and very light,” says Beneteau’s Tit Plevnik. “What is special is how calculated it is. In mass-production building, you can’t rely on precision, but we do. The boat is built to the same standard as a pure ­racing boat.”

“The moment I saw it, I knew it would be good. It’s a great-looking boat at the dock and even better with the sails up.” —Greg Stewart

Built like a race boat, the judges all agree it sure sails like one. “It’s a big 36-footer,” says veteran BOTY judge and naval architect Greg Stewart. “It’s a full-ended boat that has a hint of a scow-type bow with a lot of buoyancy forward. Looking at the numbers, what they achieved with the weight and its placement is impressive—10,000 pounds for a 36-foot waterline length is a very good number. I could tell the minute we put the spinnaker up it was a slippery boat.”

Stewart set the day’s top speed at a tick over 18 knots and says: “I remember feeling the puff hit and load the rig, and the boat just scooted off with really nice steering. It felt like a Laser when you get it in that groove and it just levitates. With the dual rudders, which are pretty long, the boat has more of a power-steering feel upwind, so it lets you do a lot of things. There’s so much control, which is a good thing because you can drive out of situations, but at the same time, it’s easy to oversteer.”

Multiple cockpit mock-ups done at ­different heel angles produced a workspace that the judges could find no flaw with. “It’s all legit, easy and clean in the pit,” Allen says. “With the four of us in the ­cockpit, we had plenty of space to move around and were never into each other.

“I was doing a lot of trimming downwind,” Allen adds. “You can feel the boat take off. It was really stable and easy to handle. The thing is light and fast, and we did push it to try and wipe it out, but it was hard to do.”

All the judges praised the clever location of the primary winches on sloped coamings, which were easier to trim from than a traditional winch-on-the-coaming setup. “They’re at the perfect height,” says judge Dave Powlison, “and with them angled like that, you don’t have to crane your neck to see the sail, and the lead is virtually override-proof.”

Also noteworthy is the generous space between the high carbon wheels and the cockpit walls that allow the helmsman to slide forward without having to step up and around the wheel. The jib trimmer has easy access to the three-dimensional clue adjustment systems, and for the pit, there’s plenty of clutches, redirects and cleats to keep everything sorted and tidy.

The standard spar, and that on the demo boat, is a deck-stepped Z Spars aluminum section with Dyform wire rigging that carries 860 square feet of upwind sail area, which Stewart says is considerable for the displacement of the boat. The mast is well aft, which really stretches out the J dimension and opens the foredeck for a quiver of headsails—for this, you’ll find two tack points on the foredeck. There are four halyards total: one for a masthead gennaker, a 2-to-1 for a code sail, a fractional gennaker, and a 2-to-1 staysail. Allen, a semi-retired sailmaker, put an estimate for a complete race inventory at $60,000, which would put the boat on the racecourse for roughly $400,000. (Base boat is priced at $345,000.)

When the race is done, however, how about that interior?

Step down the wide companionway steps into a space of design simplicity and efficiency, some of which makes you say, “Duh, of course.”

For example, there’s no ­traditional L-shaped galley to port or starboard. There is, however, a tall and slender fridge smack in the middle of the boat (that you connect to the galley with a removable cutting board to complete the L). Walk on either side of it to get forward, past the proper nav station, the fold-down dinette table in the middle with roomy 6-foot berths on both sides, a jetliner-size head with a stowaway sink to starboard, and then a gigantic V-berth that benefits from all that volume in the bow. Back aft, under the cockpit, are large quarter berths as well that easily cruise-convert into storage space for water toys, like kites, wings and foils, all of which takes us back to survey result No. 2. This is where the post-race party begins and ends.

With the usual supply-chain delays, compounded with the build and design team’s obsessive and calculated approach to getting the Beneteau First 36 perfect at Hull No. 1, its debut got off to a later start than hoped. But with early boats landing at eager dealers worldwide, Plevnik says the goal is 32 boats per year for the next two years. The BOTY judges assure us it’ll be worth the wait and give you plenty of time to start planning what you can and will do with it.

• More: 2023 Boat of the Year , Beneteau , Boat of the Year , Print Winter 2023 , Sailboats
• More Sailboats

Nautor Swan Has A New Pocket Rocket

Pogo Launches its Latest Coastal Rocket

A Deeper Dive Into the Storm 18

2024 Boat of the Year Best Recreational Racer: Z24

Brauer Sails into Hearts, Minds and History

Anticipation and Temptation

America’s Offshore Couple

Jobson All-Star Juniors 2024: The Fast Generation

• Digital Edition
• Customer Service
• Privacy Policy
• Cruising World
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

• BOAT OF THE YEAR
• Newsletters
• Sailboat Reviews
• Boating Safety
• Sailing Totem
• Charter Resources
• Destinations
• Galley Recipes
• Living Aboard
• Sails and Rigging
• Maintenance
• Best Marine Electronics & Technology

Sailboat Review: Beneteau First 36

• By Mark Pillsbury
• June 29, 2023

When France’s Groupe Beneteau purchased the Slovenian shipyard Seascape in 2018, it acquired designs, tooling and production facilities, along with a team of sailors who know how to build no-frills boats that are slippery and fast. And, yes, very fun to sail.

So much fun, in fact, that once Cruising World ’s Boat of the Year judges named winners for the formal 2023 categories, we chose to conjure up a judges’ special recognition award for the First 36 as Best Sportboat . Our dilemma, you see, was that in the fleet of 17 sailboats we considered, there wasn’t really anything quite like the First 36 in terms of size or performance. But, oh, what a ride we had.

With about 12 knots of breeze blowing up a moderate chop, right out of the chute we hoisted a full main, set the big kite and were off, pegging 10 knots SOG on a broad reach. Later, in a bit more breeze and with the reacher safely stowed, we pounded upwind at close to 8 knots under the jib and single-reefed main. Big sail, little jib—it didn’t matter. The Jefa steering and twin rudders were buttery-smooth and totally in control.

Boat of the Year judge Herb McCormick noted: “This is a boat that was conceived ­working backward from the goal of a pure, unfettered sailing experience, and it fully delivers on that score. No surprise, our colleagues at the performance mag Sailing World honored it with their top Boat of the Year prize.”

Beneteau now has two First production lines, the First SE (SE stands for Seascape Edition and includes the former Seascape 14, 24 and 27) and the ­Beneteau-conceived First 44 and First 53 ­models. Like the First and First SEs up to 40 feet, the naval architect behind the 36 is Samuel Manuard. Design is by Lorenzo Argento (designer of the 44 and 53); structural details are by Pure Design & Engineering; and interior styling is by the Slovenian industrial design studio SITO. 

The idea was to build a boat equally adept at cruising as it is at doublehanded and club handicap racing. The trade-offs involved are immediately apparent when you step aboard through the First’s open transom and twin wheels. Removable cockpit boxes (with cushions) provide seating and storage in cruise mode, or can be left on the dock to make room for a racing crew. Hardware is all top notch, from suppliers such as Ronstan, Harken, Spinlock and Antal. The First even has fittings in the cockpit sole for a drop-leaf table that can come and go, depending on the type of sailing to be done.

On deck, jib sheets are routed through adjustable downhauls and inhauls that provide endless ways to shape the head sail. Forward, a 3-foot-3-inch composite sprit does double duty as an anchor roller and place to tack down off-wind sails.

The boat we sailed in Annapolis, Maryland, was fitted with the standard aluminum rig; a carbon-fiber mast is an option, as are several North Sails packages The First’s base price, posted online, is $260,000. But well fitted out, like the boat we sailed, a more realistic number is $350,000.

The First 36 is built using construction techniques in which all components are tied together to contribute to structural stiffness. Hull, deck, and interior bulkheads are vacuum-infused and cored to add stiffness and save weight. Furniture modules are also vacuum-infused and bonded to be part of the boat’s structure. Below, there is just enough wood used for fiddles and trim to give the interior, with LED lighting, a sense of warmth.

Beneteau initially offered just one keel configuration for the First, a 7-foot-5-inch ­cast-iron fin with a T-bulb down low. An option for a shoal-draft foil of 6 feet, 3 inches is in the works.

The builder also offers just one interior layout, with twin staterooms aft and a V-berth forward. There is a single head, also forward, that includes a shower, as well as a clever fold-up sink over the toilet to ­maximize usable space.

In the salon, an L-shaped galley with a sink, a two-burner stove and an oven is to port at the foot of the companionway; opposite is a sit-down nav station. In between, on centerline, there’s a stand-alone island icebox (a fridge is an option) whose top is at counter height, making it a handy place to set things down. Forward, two outboard settees flank a drop-leaf table. Both seats would make handy sea berths ­underway. As McCormick said, accommodations are more than ­adequate for spending ­extended time aboard, ­whether en route to a regatta or off coastal cruising on weekends or vacation. 

Here’s my take on the First 36: It might not be the boat for an owner looking for all the creature comforts of home in a dockside setting, but if the idea is to get out there and go sailing, well, it might be the ideal boat. 

Beneteau First 36 Specifications

Mark Pillsbury is a CW editor-at-large and served as a 2023 Boat of the Year judge.

• More: beneteau , Print July 2023 , Sailboat Reviews , Sailboats
• More Sailboats

New to the Fleet: Pegasus Yachts 50

Balance 442 “Lasai” Set to Debut

Sailboat Review: Tartan 455

Meet the Bali 5.8

Cruising the Northwest Passage

A Legendary Sail

10 Best Sailing Movies of All Time

• Digital Edition
• Customer Service
• Privacy Policy
• Email Newsletters
• Cruising World
• Sailing World
• Salt Water Sportsman
• Sport Fishing
• Wakeboarding

• New Sailboats
• Sailboats 21-30ft
• Sailboats 31-35ft
• Sailboats 36-40ft
• Sailboats Over 40ft
• Sailboats Under 21feet
• used_sailboats
• Apps and Computer Programs
• Communications
• Fishfinders
• Handheld Electronics
• Plotters MFDS Rradar
• Wind, Speed & Depth Instruments
• Anchoring Mooring
• Running Rigging
• Sails Canvas
• Standing Rigging
• Diesel Engines
• Off Grid Energy
• Cleaning Waxing
• DIY Projects
• Repair, Tools & Materials
• Spare Parts
• Tools & Gadgets
• Cabin Comfort
• Ventilation
• Footwear Apparel
• Foul Weather Gear
• Mailport & PS Advisor
• Inside Practical Sailor Blog
• Activate My Web Access
• Reset Password
• Pay My Bill
• Customer Service

• Free Newsletter
• Give a Gift

How to Sell Your Boat

Cal 2-46: A Venerable Lapworth Design Brought Up to Date

Rhumb Lines: Show Highlights from Annapolis

Open Transom Pros and Cons

Leaping Into Lithium

The Importance of Sea State in Weather Planning

Do-it-yourself Electrical System Survey and Inspection

Install a Standalone Sounder Without Drilling

When Should We Retire Dyneema Stays and Running Rigging?

Rethinking MOB Prevention

Top-notch Wind Indicators

The Everlasting Multihull Trampoline

How Dangerous is Your Shore Power?

DIY survey of boat solar and wind turbine systems

What’s Involved in Setting Up a Lithium Battery System?

The Scraper-only Approach to Bottom Paint Removal

Can You Recoat Dyneema?

Gonytia Hot Knife Proves its Mettle

Where Winches Dare to Go

The Day Sailor’s First-Aid Kit

Choosing and Securing Seat Cushions

Cockpit Drains on Race Boats

Rhumb Lines: Livin’ the Wharf Rat Life

Re-sealing the Seams on Waterproof Fabrics

Safer Sailing: Add Leg Loops to Your Harness

Waxing and Polishing Your Boat

Reducing Engine Room Noise

Tricks and Tips to Forming Do-it-yourself Rigging Terminals

Marine Toilet Maintenance Tips

Learning to Live with Plastic Boat Bits

• Sailboat Reviews

Beneteau First 36.7

This dual-purpose boat, designed by bruce farr, is more user-friendly than its high-performance progenitors, but will still sail fast as a one-design or in handicap fleets..

From her office in France, Madame Annette Beneteau Roux, granddaughter of her company’s founder, Benjamin Beneteau, oversees the largest boatbuilding company in the world.

In the US, the Beneteau and Jeanneau brands are madame’s two most popular lines. Under the banner of Beneteau USA, the company markets the Beneteau line, once known as Oceanis models, as distinguished from the First line of performance cruisers. Historically, the Beneteau marque has been stamped on a cruiser with a distinctly European flair. However, recent French-European styling is less pronounced than in boats introduced 10 years ago. They can generally be characterized as having a turn of speed, spacious accommodations, and pricing competitive with American production builders.

First models are sportier, more aggressive designs, and typically exhibit better performance than their more conventional sisters, though they sacrifice little of their appeal for those seeking creature comforts.

Like its competitors, the company has experienced its share of production and blistering problems. However, refinements in raw materials and construction methods are resulting in fewer production glitches.

Most Beneteau boats designed for use in the US are constructed in Marion, South Carolina. The 36.7, however, was the first of the First line to emerge from that production facility in several years. Since its unveiling in the fall of 2001, 100 of the 36.7s have been sold in the US.

The first collaboration of the Bruce Farr design office with Beneteau resulted in the 1992 introduction of the First 45s5. More recently, Farr designed the First 40.7, which the company claims is the most successful performance yacht of its size in the last 20 years. It has a stellar record racing under IMS handicapping.

Though they share a similar pedigree, the 36.7 was not designed to meet a racing rule. Still, whether she’s steered with the big stainless steel wheel preferred by the American market, or with a tiller, which seems to be the choice in Europe, the boat ‘s work zone speaks plainly of performance, with a big mainsheet traveler that spans the cockpit, and efficient grinder stations forward of that.

In profile she displays a flat sheer, plumb bow, and reverse transom. These shapes are getting downright common today, thanks, probably, to the influence of European offshore racing boats. The new J/109 is shaped very similarly.

The swept double-spreader rig with large mainsail and comparatively small foretriangle is another trend of recent years, and a welcome change from the IOR-influenced sailplans that held sway in production cruising boat design long after the IOR itself faded.

The underwater hull of the 36.7 is quite slippery, with two nicely shaped keel options-one that gives a draft of a bit over five feet, the other a bit over seven.

Among Bruce Farr’s early creations is Design #51, a 36′ one – tonner known as the 1104. It was so fast that it allegedly caused the IOR to revise design criteria. Although not as flatout as the 1104, the 36.7 can be seen as a direct descendant. Comparing the differences between the two, Jim Schmicker of the Farr office says, “The 1104 was designed primarily for the New Zealand and Australian markets, where proportionately less sail is needed because of windy sailing venues. “The 36.7 has similar sail area to wetted surface ratios, but carries more cloth because it’s 25% heavier.”

The new Beneteau was driven by a “different design requirement that requires a more luxurious interior while at the same time producing a fast boat.”

The 36.7 is also an offshoot of the Beneteau 40.7, although Schmicker says the 36.7 “has a more advanced hull shape and refined look when heeled at high angles.” That heeled shape, combined with what the Farr office calls a “generous rudder area,” simply means that the rudder keeps its bite in the water when the boat is reaching in big winds.

“The changes are more noticeable when the boats are side by side,” says Schmicker. “The 36.7 is straighter in plan at the sheer, with less curvature than the 40.7. It has less volume above the waterline amidships because more volume was placed in the ends. The result is a longer heeled length, producing good handling throughout the heeled range.

“We created the same interior layout in a boat that is nearly three feet shorter. However, there’s less space between the stem and V-berth, and aft berths and transom.

“With the keel design it’s all about laminar flow. This keel on the 36.7 is the result of years of intensive research that produces airfoils designed specifically for the boats that we design. They don’t come from the pages of a NACA foil book. They are the result of 15 years of IOR, IMS, America’s Cup, and Volvo Race research. We provide complete 3D representations to Beneteau so they can produce our designs accurately. The objective is to design the smallest rudder with the maximum lift and low drag that will withstand high loads in heavy winds without stalling. We place the rudder shaft in the blade and set the sweep of the blade tip to give the right amount of helm load for all conditions. We also want robust sections that don’t stall abruptly. And, they must be able to be made in a mass production line that produces the same surface finishes.”

Beneteau USA president Wayne Burdick points out that many yacht designers are surprised “if a boat comes within 1,000 pounds of her designed weight,” because boats tend to put on weight in the production process. However, the weight target is critical to one-design racers, who expect a level field. Schmicker says that the collaboration between the Farr office, Beneteau production managers, and Sparcraft, which builds the mast and boom, yielded a prototype within 100 pounds of targeted weight, and the first boat off the production line was “spot on.”

Deck Layout

Like other aspects of the boat, excepting the massive wheel and location of the traveler, the deck arrangement is typical of many production boats.

Halyard and mainsail controls are led aft to Spinlock ST clutches on the cabintop. Jib and spinnaker sheets are led to Lewmar 48 and Lewmar 40 selftailing winches. The solid vang is supplied by Sparcraft.

Cockpit seats are 19″ wide, 15″ high, and 52″ long, and accented by teak veneer. Though the cockpit arrangement appears conventional, a Farr touch is that it is a convertible: Seats port and starboard with shallow storage compartments below may be removed to make space for sail trimmers, shortening seats 20″.

Length on the centerline between traveler and companionway is 58″, and the width of the footwell is 39″.

With room for the helmsman and a passenger in the stern, she seats seven comfortably in cruise mode, about what we’d expect in a boat this size.

From the perspective of a nonracer or shorthanded sailor, the big wheel is an obstacle in getting to the traveler, and the traveler is an obstacle in getting to the companionway or back to the stern. Singlehanders will need to be nimble, especially when trying to work the sail controls on the cabintop.

An excellent footrest provides a brace for the driver. An additional brace on the cockpit sole would increase crew comfort when heeled. An instrument pod at the companionway provides helmsman and crew with excellent visibility while avoiding the risk of the “knee-through-the – instrument-lens” repair job.

Since the mainsheet is located at the end of the boom, it allows guests to sit in front of the traveler, or move below easily. That layout is a refreshing change, since many builders locate mainsail controls on the cabintop, with mid-boom sheeting. That compromise does prevent interference of the mainsheet with guests, but often at the expense of good sailtrim and efficiency.

Our test boat lives in rainy Washington, where year-round sailing mandates a dodger. Properly fitted, it doesn’t interfere with movement of skipper or crew while underway.

At one end, the bow sports an anchor roller and locker. A foot brace molded into the foredeck, double lifelines, aggressively patterned non-skid, and a teak toerail provide a bowman with a safe working area.

At the other end, the stern seat is removable to ease boarding. A telescoping ladder, shore power, and cockpit shower are standard equipment. A liferaft can be stowed below the helm seat.

There’s little storage in the cockpit, since quarterberths occupy spaces on both sides belowdecks. A small storage area in the starboard quarter provides room for fenders and lines. Most cruisers will sail with a genoa on a furler, and racers underway will keep sails amidships and forward, but still, a boat this size will always have gear that’s best stowed in a cockpit locker or lazarette-bucket, hose, shorepower cable, maybe a grill, and so forth. Much of that will have to live below, and the smaller aft cabin is the likely candidate for “shed.”

The layout of the 36.7 is a smaller version of that on the 40.7. The saloon provides seating for six, and there are bunks for seven, but tall people’s toes will be closer to the ends than they are on some comparable boats.

The appearance is traditional (that is, without the Philippe Starck stylized interior that Beneteau used on many of its boats). The saloon measures almost 10′ on the centerline. There’s 6′ 2″ of headroom, and 8′ of clearance between the settee backs. Settees are 6′ 4″ long and 2′ 1″ wide, and will double as berths if leecloths are installed.

The versatility of design is reflected in the saloon table: When in place it provides a surface for four to six diners; remove it, and its stainless steel support provides a foot brace for crew when underway.

Removal of the table also eases sail packing when in race mode. On our test boat, the brace also provided a space between settee and footrest for a 25-gallon plastic storage bin that holds lifejackets and crew gear. However, if the table is not stored in the garage, odds are it will be atop a bunk.

The L-shaped galley to port is small but adequate, equipped with a twoburner stove and double sink. A counter covers a 24″ deep x 17″ wide reefer located outboard that needs shelves or portable baskets to be organized. Storage is in enclosed cupboards with teak doors, and opening ports provide ventilation.

To starboard, the nav station faces forward and is fitted with wood cabinetry large enough for mounting electronics and fuse panels. The chart table measures 31″ x 23″-large enough for use with a folded chart.

Storage drawers and shelved compartments are below the chart table and navigator’s seat. In a world in which gear expands to fill the space available, the well-organized skipper will find room for necessary gadgetry, but with little space left over.

The master stateroom is furnished with a V-berth measuring 6′ 1″ long and 5′ 3″ wide at the head. The cabin also has a hanging locker and shelves on the hullsides.

Since Americans’ preferences in sleeping quarters differ from their French counterparts, US boats were reconfigured to suit the marketplace. Rather than having equal-sized spaces in the aft staterooms separated by a bulkhead on the centerline, the bulkhead has been moved outboard to starboard. As a result, the bunk to port is nearly queen-sized, while the one to starboard is basically a single quarterberth with some privacy-actually an ideal sea berth.

The head compartment on any three-cabin, 36′ boat will be, at the least, a designer’s challenge. On this boat, a clear choice was made, and the head is Lilliputian. With six feet of headroom, crew can brush teeth while standing, but showers will be taken while seated on the toilet with little space left for swinging arms. On the plus side, small head compartments in which elbows and knees can be wedged against bulkheads are best in a seaway (if any head in a seaway can rate above “dismal”), and this space is shiny fiberglass, vented overhead- so it will be low-maintenance.

Construction

Since Beneteau promotes the 36.7 as a one-design racer, it’s being produced with close scrutiny of the weight and application of raw materials. Boats are constructed to CE Class A requirements for unlimited offshore use.

Mike Thoney of Beneteau says the laminate, laid up behind the gelcoat with glass and vinylester resin, is precut to assure proper dimensions. Beneteau has discontinued use of the Beneteau Underwater System in favor of vinylester resins designed to prevent osmotic blistering. The company is mixing resins to its own formula. Mike Thoney declined to provide details about the mix.

Internal structure is a one-piece grid used in most models that reinforces the hull and distributes mast and keel loads. It also provides a bed for bulkheads and furniture, engine mounts, keel, chain plates and tankage.

Bulkheads become part of the structure when they are bonded to both hull and deck. Chainplates are attached using tie rods molded into the grid system.

The hull-deck joint is an inwardoriented flange onto which the deck is laid and secured with PU 501, a proprietary polyester glue, and mechanical fasteners through-bolted through deck and toerail.

“The deck is laid up with a skin coat, layers of precut fiberglass, and cored with balsa,” Thoney says. “Hardware is all bolted through solid glass and secured with backing plates. Where it goes through coring, the coring is removed and replaced with fiberglass. Backing plates for stanchion bases are bedded in putty to avoid movement. Engine mounts are through-bolted and secured with backing plates and nuts.”

On our test boat, 31 keel bolts and plates designed to disperse loads were easily accessible in a shallow bilge. A robust mast boot prevents water from intruding. In the three rainy months before our inspection, no water had appeared in the bilge. Water and fuel tanks are form-fitted to beds and secured with stainless steel rods. A holding tank is held in place by straps.

Joe Foss, service manager for Beneteau USA, described three post-production problems:

First: “The Edson steering system was designed with a short drag link that inhibited steering, depending upon the angle it met the wheel during the commissioning process. When several boats experienced the problem, the link was lengthened. A repair kit was distributed to the owners of hulls 1-33.”

Second: “A washer at the stemball on one of the shrouds (D-2) was so small it pulled through the spreader bar. Though the problem was encountered only on one boat, hulls 1-43 were examined and found sound.”

Third: One of the boats experienced a broken spreader bar. Since the same spreader is used on the 40.7 and 42.7, and more than 11,000 have been produced with no failures, Foss considers this an anomaly.

Performance

During a test sail near the Olympic Peninsula, we immediately discovered that she’s a responsive yacht. She easily backed out of the marina into a three-knot current with wind on the beam. A 29-horsepower Volvo sail drive provided quick acceleration and produced a short turning radius.

Crewed by a 62-year-old retiree and his small wife, sailhandling proved easy, with an autopilot holding her nose into a stiff breeze. We sailed with 12-13 knots displayed on the wind indicator with full mainsail and 105% genoa. The helm was perfectly balanced, though she felt slightly underpowered.

In 15 knots of wind, we sailed closed hauled at six knots. Footing off to a beam reach, speed held steady at 7.2-8.0 knots, and we steered with two fingers. As we sailed down below a broad reach, speed dropped to 5 knots. In these conditions, a shorthanded crew could hoist an asymmetrical spinnaker and keep the speedo scrambling.

With more than 100 boats sold since its US introduction, the 36.7 is already a success. The base price has increased approximately 10% since its introduction, to $135,000, sailaway, FOB the factory. However, an autopilot adds $2,065; an electronics package with VHF, Raytheon ST60 Tridata, and wind instruments $2,155; and Harken split- drum roller furler $1,695.

For racers, spinnaker gear and an aluminum pole will add $2,505 to the pricetag; a carbon pole adds $1,145.

We suspect that the J/109, mentioned earlier, would be natural competition for this Beneteau, both for one-design fleet racers and performance cruisers. Compare some of the J boat’s specs-LOA 35′ 3″, LWL 30′ 6″, beam 11′ 6″, standard draft 7 ‘, DSPL 10,500 lbs., SA/DSPL 21, DSPL/ L 165-to the Beneteau’s numbers. By those numbers, the J is just a trifle more moderate, and quite a bit higher priced at $165,500 for the base boat. That price differential may have to do with costs associated with the SCRIMP building technique used by JBoats, or with differences in standard hardware and fittings, or maybe with economies of scale-although J/Boats is hardly a low-production builder.

But back to the 36.7. She’s quite nimble. She goes faster and points higher in light air than standard production cruising boats her size. As a racer she’ll be competitive in a onedesign or handicap environment.

Beneteau has laid out restrictive onedesign fleet rules designed to control cost and promote competition among amateurs. There’s an “owner-driver” rule, and boats may not be stripped of standard equipment for racing purposes. Sail inventories are limited to four sails that can only be replaced at 12-24 month intervals.

This enhanced performance, combined with comfortable, functional accommodations and a good price, should attract a broad-based market. She won’t be as comfortable as a fullkeeled cruiser when pounding into big seas, but the adaptable sailplan will allow a shorthanded crew to fly big genoas on a furler easily, or an asymmetrical spinnaker almost as easily as a sprit boat-as long as they’re nimble enough to jump around the wheel and over the traveler.

The lack of cockpit-accessible stowage space is a shortcoming, partly balanced by the good sense of the aft cabin arrangement below. The size of the head compartment really is a matter of preference, and on a race boat or offshore boat, small is fine. Belowdecks, owners will more likely curl up with a book than a television remote, and that, too, is fine.

RELATED ARTICLES MORE FROM AUTHOR

Wow, I raced a Yankee 30 out of Olympia WA for 3 years as crew. I was 19 at the time and had to drive 3 hours from the NAS on Whidbey Island to the boat for each regatta. This was my 1st sailboat to sail on as a beginner. You have a nice boat.

I am looking to buy the Beneteau 36.7 to replace my Elite 37 (made in France) because I had planned to charter my own boat (I hold a 50 GT certificate) and need a boat made in the US.

How can you tell if the 36.7 was made in SC?

Capt. Charlie D

LEAVE A REPLY Cancel reply

Log in to leave a comment

Latest Videos

Island Packet 370: What You Should Know | Boat Review

How To Make Starlink Better On Your Boat | Interview

Catalina 380: What You Should Know | Boat Review

• Privacy Policy
• Do Not Sell My Personal Information
• Online Account Activation
• Privacy Manager

First 36.7 Deep draft

Sailboat specifications.

• Last update: 15th March 2020

First 36.7's main features

First 36.7's main dimensions, first 36.7's rig and sails, first 36.7's performances, first 36.7's auxiliary engine, first 36.7's accommodations and layout, first 36.7's saloon, first 36.7's fore cabin, first 36.7's aft cabin.

Similar sailboats that may interest you:

× You are using an outdated browser. Please upgrade your browser to improve your experience.

We Ship Worldwide! | FREE SHIPPING! for US Continental orders over $99. Click for details.

Shopping Cart

Your cart is currently empty..

FREE SHIPPING! for US Continental orders over $99 click for details

Beneteau First 36.7 - Sailboat Data, Parts & Rigging

Sailboat data, rig dimensions and recommended sail areas for Beneteau First 36.7 sailboat. Tech info about rigging, halyards, sheets, mainsail covers and more.

Sailboat Data directory for over 8,000 sailboat designs and manufacturers. Direct access to halyards lengths, recommended sail areas, mainsail cover styles, standing rigging fittings, and lots more for all cruising and racing sailboats.

MAURIPRO Sailing offers a full range of sailboat and sailing information to help you find the correct sailboat part, one that properly would fit your sailboat and sailing style. Our sailor's and sailboat owner support team are ready to talk with you about your specific sailing needs, coming regatta, or next sailing adventure.

From all at MAURIPRO, let's Go Sailing!

Copyright © 2024 MAURIPRO Sailing LLC.

Beneteau 361

The beneteau 361 is a 36.42ft masthead sloop designed by berret racoupeau yacht design and built in fiberglass by beneteau since 1999..

The Beneteau 361 is a light sailboat which is a reasonably good performer. It is reasonably stable / stiff and has a low righting capability if capsized. It is best suited as a coastal cruiser. The fuel capacity is originally small. There is a good water supply range.

Beneteau 361 for sale elsewhere on the web:

Main features

Login or register to personnalize this screen.

You will be able to pin external links of your choice.

See how Sailboatlab works in video

We help you build your own hydraulic steering system - Lecomble & Schmitt

Accommodations

Builder data, other photos, modal title.

The content of your modal.

Personalize your sailboat data sheet

• Oceanis 30.1
• Oceanis 34.1
• Oceanis 37.1
• Oceanis 40.1
• Oceanis 46.1
• Oceanis 51.1
• Oceanis Yacht 54
• Oceanis Yacht 60
• FIGARO BENETEAU 3
• Heritage Sailing Yacht
• Flyer 7 SUNdeck
• Flyer 7 SPACEdeck
• Flyer 8 SUNdeck
• Flyer 8 SPACEdeck
• Flyer 9 SUNdeck
• Flyer 9 SPACEdeck
• Antares 7 Fishing
• Antares 8 Fishing
• ANTARES 11 FLY
• Gran Turismo 32
• Gran Turismo 36
• Gran Turismo 41
• Gran Turismo 45
• Swift Trawler 35
• Swift trawler 41 Sedan
• Swift trawler 41 Fly
• Swift Trawler 48
• Grand Trawler 62
• Heritage Powerboats
• Future Owners
• A REMARKABLE ANNIVERSARY
• Our History
• Our Architects and Designers
• Our philosophy
• Our Innovations
• Your way to ownership
• Event calendar
• Tests and Awards

Oceanis Clipper 361

• Description

The Clipper 361 is a powerful and seafaring sail boat which will take you wherever you wish, in the best possible conditions. Innovative in terms of sailing pleasure and comfort, the Oceanis Clipper 361 will also captivate you with the thoroughness of its construction, a guarantee of many years of unforgettable cruises. 

Naval designer :  Jean BERRET ; Olivier RACOUPEAU

exterior design

Interior design

Evening on the BELEM Tall ship After Naming

#spreading hope

Ahoy: and Atlantic tour on an Oceanis to raise people’s awareness of cystic fibrosis

Together, we would like to fill people with new hope

Pousse par le vent : Sailing in the caribbean !

After three months in Martinique, our adventurers put out to sea again on Maloya!

Customer Care

Buying a BENETEAU doesn’t have to be a daunting task. We have teams of experts to guide you through the entire process – everything from sea trials, financing, and customization to after-sale commissioning, service, and maintenance. We are proud to have one of the largest, most highly-regarded dealer networks in the world. We’re ready to provide you with the assistance and expertise needed to launch you and your BENETEAU on a lifetime of happy, rewarding, and memorable voyages.

Other models in the range

Oceanis Clipper 523

Oceanis Clipper 473

Oceanis Clipper 423

Oceanis Clipper 411

Oceanis Clipper 393

Oceanis Clipper 381

Oceanis Clipper 373

OCEANIS CLIPPER 343

OCEANIS CLIPPER 331

OCEANIS CLIPPER 323

OCEANIS CLIPPER 311

Select your area and your language

• Chinese, Simplified