ASA / American Sailing

  • Find A School
  • Certifications
  • North U Sail Trim
  • Inside Sailing with Peter Isler
  • Docking Made Easy
  • Study Quizzes
  • Bite-sized Lessons
  • Fun Quizzes
  • Sailing Challenge

What's In A Rig, Wing Sail

What’s In A Rig? – Wingsail

By: Pat Reynolds Sailboat Rigs , Sailboats

What’s in a Rig Series # 8 – The Wingsail

Although wingsails or rigid wings have risen to the limelight in the contemporary sailing world with the America’s Cup now employing the technology across the board, they are in no way a brand new concept. A sail, after all, in its purest form is essentially a wing. So, through the decades, many designers, looking for optimum performance, have of course instituted rigid wings (just like that of an airplane). A notable example would be the so called Little America’s Cup, a long-standing catamaran contest based around the pursuit of pure speed.

The efficiency of a hard wing has never been in question. They sail upwind higher and reach faster. Their purity of engineering allows for maximum proficiency. When compared to a solid wing, a soft sail is full of hard to manage variables. The shape, components and accompanying systems are no match for a wingsail. In many ways, a conventional sailboat rig is fighting against itself to do what it’s meant to do. Shrouds and stays are battling to keep everything in place while a sailor adjusts control lines incessantly. It’s not perfect. However, the relative practicality is another issue. A very large unbending non-folding solid structure has its obvious drawbacks. How do you stow this thing when you’re done sailing and how do you reef it if the breeze starts blowing and, for the traditionalists, where’s the romance in a big airplane wing sticking up from the front of the boat?

Before we address those questions, let’s look at how this rig works. Using the America’s Cup boats as great examples, a wingsail itself is usually composed of two parts and the surrounding system is essentially three ingredients.

The sail has a forward and trailing element. The trailing element is like the flaps on an airplane wing and the angle between the two elements is called camber. Increasing the camber (angle) produces power. If the power becomes too much, which it often does, another control system comes into play that deals with “twist”. Twist allows the ability to depower the boat by twisting the wing so wind can spill off.

After camber and twist, the third major aspect of control on these quite simple wing setups is the mainsheet. Like a normal mainsheet, it lets the sail out, but unlike a soft sail, a rigid wing doesn’t power up downwind, which is why soft genoas are often part of the sailplan.

So, without argument wingsails are more efficient engines, but, as we stated, are not nearly as practical as soft sails. Are you sensing the idea of a hybrid coming around the bend? Yes, in fact, world renown cruising boat manufacturer Beneteau has been developing just such an innovation. They have a soft wingsail prototype installed on a production boat that blends the two concepts. It’s made of cloth so it can be broken down like a traditional scale but is, in every other way, a wingsail. It’s an unstayed mast with an airplane style wing that they say behaves very much like its rigid cousin.

So, lets revisit the particular questions we asked earlier and make sure we answered them. How is the wingsail reefed? By adjusting the aforementioned twist control, a wingsai is depowered, thereby reefed. How can this big wing thing be stowed? Well, with this hybrid idea, it’s lazy jacks and sail covers – we know how that works.

The last question is more difficult to answer…where’s the romance? The feeling, sounds and shape that soft sails embody date so far back into our collective history, it’s a bit heartbreaking to think they could possibly be replaced. There’s a certain humanity…a beauty and art involved in harnessing these inherent imperfections. We share this struggle and achievement with those who sailed before us. We have continually developed materials, hardware and better systems to get an edge, and are always happy when we succeed, but a radical refit, should it happen on a grand scale, is sort of jarring and sad.

Alas, this is the quandary of technology and advancement. Change bringth and taketh away. But don’t worry too much about it – in this modern day it seems 18-year old yellow, fading Dacron sails hung about on aging wires are still representing strong!

What's in a Rig Series:

sloop rig

Related Posts:

featured-image_zhik-partnership

  • Learn To Sail
  • Mobile Apps
  • Online Courses
  • Upcoming Courses
  • Sailor Resources
  • ASA Log Book
  • Bite Sized Lessons
  • Knots Made Easy
  • Catamaran Challenge
  • Sailing Vacations
  • Sailing Cruises
  • Charter Resources
  • International Proficiency Certificate
  • Find A Charter
  • All Articles
  • Sailing Tips
  • Sailing Terms
  • Destinations
  • Environmental
  • Initiatives
  • Instructor Resources
  • Become An Instructor
  • Become An ASA School
  • Member / Instructor Login
  • Affiliate Login

GET STARTED

FREE PRINT & DIGITAL EDITIONS

Epoxyworks

Cover Article

rigid wing sailboat

  • Weird & Wonderful
  • Sports Equipment
  • Carbon Fiber
  • Boat Construction
  • Composite Fabrication

Rigid Wing Sails

By: Epoxyworks Community

Spring 1993

by John Holtrop

Epoxyworks 2

Rigid wing sails offer high aerodynamic efficiency. They have been used in defending the America’s Cup, and are seen on some other high performance catamarans.

Aerodynamically, a rigid wing sail is identical to an airplane wing. Both reward increased lift and decreased drag. However, airplane wings are simple to design since they fly with a fairly constant angle of attack. So an airplane wing’s shape or camber can be optimized for a normal set of flight conditions. Sailboats, on the other hand, must operate under frequently changing conditions. For example, tacking a sailboat forces the airfoil shape of the sail to completely reverse itself, and wind velocity changes require that the sail’s camber and surface area be adjustable.

In the past, rigid wing sails for sailboats used hinged flaps and complex control mechanisms to achieve this flexibility. These designs were heavy, complicated, expensive, and impossible to reef or stow. Obviously, cloth sails are more practical for normal sailboats. Cloth sails are relatively simple and cheap. They can be stretched into many different shapes with simple control lines. For most sailboats, the increased efficiency of a rigid wing is not worth the bother.

A rigid wing sail’s extra efficiency (increased lift and reduced drag) is best utilized on wind surfers, ice boats, land sailors or other high speed applications. The biggest problem is designing a simple, light weight rigid wing sail. Modern composite materials make it possible to combine the efficiency of a rigid wing with the simplicity of a cloth sail.

Thin composite parts will bend easily without cracking, and these are many times stronger and stiffer than the best sail cloth. Thicker sections (solid or cored) can be added at specific locations where stiffness is critical. This allows one part of a composite structure to be rigid, while other areas are flexible. Composite materials (carbon fiber, aramid, honeycomb, foam etc.) can be added to optimize strength, stiffness and weight.

The wing sail concept combines a thick, rigid airfoil nose with a flexible center body and thin trailing edge. The wing sail is molded from composite materials in the form of a symmetrical airfoil. If the wing sail is rotated into the wind slightly, aerodynamic forces buckle the windward side of the flexible center inward and pull the lee side out. These flexible areas then deform smoothly into a shape resembling a conventional cambered rigid airfoil. The amount of camber is controlled by the out haul tension and the stiffness of the materials, just like a cloth sail. When tacking, the flexible surfaces snap over to the other side, and the camber shape is reversed (as with cloth sails). The rigid leading edge is stiff enough to handle all bending loads, eliminating the need for a traditional mast and shrouds.

While the basic concept is simple, the exact shape that the deformed wing sail will take and its efficiency, is difficult to predict without building a prototype. Some excellent research has been done on flexible airfoils, both single and double sided, with a variety of leading edges. Much of the airfoil theory in the following design was gleaned from an article written by Mark D. Maughmer (Department of Aeronautical and Astronautical Engineering, University of Illinois, Urbana) titled “A comparison of the aerodynamic characteristics of eight sailwing airfoil sections” (#N79-2389, 1972). Mark’s paper predicts at least a 50 percent lift/drag improvement for a thick, double surface airfoil, over a conventional sail/mast combination.

Theories are important, but the real proof is how well a full size operating prototype performs. I selected a wind surfer for the prototype, in order to reduce cost, weight and labor. Three years and many labor-hours later, I finally put the theory to test.

I selected dimensions based on a standard 60-70 sq. ft. wind surfer sail. Since the rigid sail was more efficient, I designed it one-third smaller, for a total of 40 sq. ft.:

  • Length                         152″
  • Max chord (width)        52″
  • Head                             26″
  • Foot                              30″
  • Maximum thickness     6″

The thickness of an airfoil is usually expressed as a percentage of the chord. For low-speed efficiency, 12 to 18 percent is typical. I selected the lower value, 12 percent, to keep size and weight down. The leading edge shape was taken from a NACA (National Advisory Committee for Aeronautics) #63 cross section, which has a fairly sharp elliptical nose. I basically guessed at these values. They looked reasonable, but other NACA shapes and thicknesses may be more efficient. I attached the wishbone to a piece of tubing glassed into a socket molded behind the leading edge, and laced it to the clew with a four-to-one out haul. Then I bonded a tapered “C” section spar inside of the wing, from head to foot, at the 1/4 chord line. It terminated with a 12 inch tube, which contained a standard BIC sailboard gooseneck fitting. This spar, and the rigid leading edge, carry all of the bending loads and form a watertight chamber, providing several hundred pounds of flotation.

I built up a plug (top photo) from wood strips, and used it as a male mold for the rigid elliptical nose and tapered spar. Next, I attached plywood sides to the base of the plug to form a tear drop cross section. After I filled, sanded, and sealed the plug, I coated it with a fiberglass release film. Then I laid two layers of 60oz fiberglass over the entire plug, adding several extra layers in the nose region.

I pulled off the cured part, and glassed foam strips to the inside for increased stiffness. Next I molded a “C” section main spar to fit the plug base, fitted it to the nose (bottom photo), and glassed it into its final position. I added two layers of inch-wide, unidirectional graphite fiber to the spar caps to increase bending stiffness.

I molded the single surface trailing edge, on a flat plywood form, from two layers of 7-ounce Kevlar cloth. The unsupported trailing edge was a little too flexible, so I added three foam battens (1/4″ x1″x18″) to one side, about 24 inches apart. The openings at the head and foot of the double surface section, I filled with foam plugs, rounded, and glassed watertight.

To stress test the finished structure, I stood in the center of the spar while it was supported at both ends. My 190 pounds deflected the wing about half an inch, causing some creaking, but it held. With a fresh coat of paint and fitted with a wishbone and gooseneck, the finished sail weighed 36 pounds. This is 10 to 15 pounds heavier than a conventional rig.

Now for the moment of truth! Three of us trucked my BIC sailboard and the wing sail over to Lake Isabella in Kern County, Calif. Known for good wind, Isabella is a very popular lake for wind surfing. When we arrived, the winds were medium, about 15 knots, with occasional gusts to 20. Everyone was using big sails. The three of us tested the wing sail for the next four hours. We didn’t blow anyone off the lake, but we got a lot of attention and learned a great deal about the design.

Good features

1. The wing was very sensitive to changes in “angle of attack.” It could be feathered easily, then generate lift with just the slightest pull on the wishbone. At speed, the wing seemed to have a narrow “sweet spot,” and the rider could dump power very quickly. This made gusts easy to handle, and was predicted in Mark’s article. His data showed the L/D curve for a double-sided sail to be narrow. The single-sided conventional sail has a flatter L/D curve, and is not as sensitive to small changes in the angle of attack.

2. The wing was much stiffer than a standard rig. There was no “give” during gusts or when pumping. Twist was not excessive, and the trailing edge (leech) was stable and did not flutter.

3. The double surface section responded to air loads very nicely. The deformed shape looked like a “real” airfoil, and could be controlled without out haul tension. Due to the stiffness of the wing, the out haul had to be quite loose to develop the proper amount of camber for this wind condition. This made the wishbone feel sloppy, but did not cause control problems.

4. Speed was only slightly less than other similar wind surfers. During gusts the boat accelerated well, and matched speed with other boats. The general feeling was that our boat was performing well for such a small sail and light wind. Twenty-five knots winds, or a 60 sq. ft. sail,` would have been ideal.

5. The rig floated high in the water and was easy to up haul. We didn’t attempt any water starts, but the wing lifted well, and beach starts were easy.

Undesirable features:

1. The sail area was too small for the wind condition, and we had no easy way to increase it. With the advantage of hindsight, I would design the upper three feet to be removable. A larger than normal sail might work with a wing sail, since it luffs cleanly and very quickly. This would help under strong wind conditions.

2. With the out haul loose for more power, the wishbone felt sloppy. A “slip joint” out haul would hold the wishbone firmly, and still allow for camber adjustment. A one-to-one purchase is adequate, since the wing sail is so rigid.

3. When the wing was dropped, the rigid foot area hit the side of the board. Unlike cloth, the fiberglass would not give, so the foot of the sail ripped about 12 inches. This let water into the center section, but the damage did not get any worse, or effect performance. The foot section needs to be heavier, and padded like most goosenecks.

4. Thirty six pounds is a little too heavy. Using a foam core leading edge and thinner laminates could save five pounds, maybe more. On a larger boat, the extra weight may be offset since halyards, shrouds, turnbuckles, and chain plates are not needed.

5. Visibility behind the wing is poor. Clear windows could be stitched or laced into the sail.

I think these tests show that the basic concept is sound, and practical for some applications. Thick, well shaped, double surface airfoils are more efficient than cloth sails. Composite materials can be designed to deform into a smooth aerodynamic shape under air loads, without complicated flaps, hinges, and control lines. The bending and torsional stiffness in the leading edge is very high, and a free-standing rig is a definite possibility for larger sailboats. The design has a lot of potential for ice boats, sand sailors, and very high speed sailboats.

rigid wing sailboat

Boat Building & Repair

rigid wing sailboat

Jacques Coon’s Drift Boat Build

rigid wing sailboat

Building a Strip Kayak

rigid wing sailboat

Swim Platform Rebuild

"DN Iceboat Building" by David Fortier - Epoxyworks 57

DN Iceboat Building

IMAGES

  1. New Rigid Wing Sail

    rigid wing sailboat

  2. Figure 2 from Novel Rigid-Wing Bi-Directional Sailboat Design and Method of Sailing

    rigid wing sailboat

  3. Duckworks

    rigid wing sailboat

  4. Free STL file Rigid Wing Sailboat. 🪶 (SCAD)・3D printable model to download・Cults

    rigid wing sailboat

  5. The design of soft wing sails for cruising

    rigid wing sailboat

  6. Rigid Inflatable Boats

    rigid wing sailboat

VIDEO

  1. Spring Millennium flights.March 2012

  2. Exxtacy Rigid Wing Launching and Landing

  3. ATOS- C Landing in Ellenville

  4. Wing_on_Wing_March 25th.wmv

  5. 3 9 2024 Woolers vr1

  6. Klingberg Wing MkI Rigid Wing Hang Glider

COMMENTS

  1. Wingsail - Wikipedia

    Wingsails are of two basic constructions that create an airfoil, "soft" and "hard", both mounted on an unstayed rotating mast. [4] Whereas hard wingsails are rigid structures that are stowed only upon removal from the boat, soft wingsails [5][6] can be furled or stowed on board. [4]

  2. Rigid wing sailboats: A state of the art survey - ScienceDirect

    This paper presents a state of the art survey of rigid wing sailboats primarily based on available literature. Several examples of sailing ASV already developed, or under development, at academia as well as of commercial products were presented.

  3. Rigid wing sailboats: A state of the art survey | Semantic ...

    This work addresses the design, modeling, and simulation of a land yacht probe equipped with a rigid free-rotating wing sail and tail flap and proposes a novel design and simulation method for free rotating wing sail autonomous land yachts.

  4. What's In A Rig? - Wingsail - American Sailing

    After camber and twist, the third major aspect of control on these quite simple wing setups is the mainsheet. Like a normal mainsheet, it lets the sail out, but unlike a soft sail, a rigid wing doesn’t power up downwind, which is why soft genoas are often part of the sailplan.

  5. Rigid Wing Sails - Epoxyworks

    A rigid wing sails extra efficiency (increased lift and reduced drag) is best utilized on wind surfers, ice boats, land sailors or other high speed applications. The biggest problem is designing a simple, light weight rigid wing sail.

  6. Aerodynamic Analysis and Design of High-Performance Sails

    High-performance sails, such as the ones used on the America Cup boats, require sails whose aerodynamic characteristics approach those of rigid wings, yet permit a reduction in sail area in high wind and sea conditions. To this end, two-cloth sails are coming into use. These sails are constructed out of an articulated forebody that