sailboat two masts

What Is A Boat With 2 Masts Called?

Two-mast sailboats hold special places in many sailors’ hearts. In addition to being dignified and majestic, a two-mast sailboat offers a perfect balance that can be easily achieved by adjusting the masts in many different ways. Let’s look at the different types of two-mast sailboats.

Whether you’re a sailboat fanatic or an interested observer, there’s something special about two-mast sailboats. In most cases, the first thing you’ll notice about a sailboat is the two masts. Generally, the mainmast is often taller than the aft-mast, which is often referred to as the mizzenmast. The mizzenmast is like a trusted old friend. It not only helps in stabilizing the sailboat under power but can also act as a bow thruster in certain scenarios. There are many reasons why sailors sing a lot of praises as far as two-mast sailboats are concerned. In heavier winds, you can break down the main mast and use the mizzen mast to give you a more balanced and comfortable sail even in the worst of conditions. But what is a boat with 2 masts called?

There are several sailboats with two masts. The most common ones include yawl, ketch, schooner, and brig. In most cases, the designs of the masts do vary but the main idea remains the same. They can have the extra mast either behind or in front of the mainmast. If the additional mast is in front of the mainmast, it’s known as a foremast but if the additional mast is behind (aft of) the mainmast, it’s known as a mizzenmast.

Let’s take a brief look at these two-mast sailboats.

Table of contents

A yawl is one of the most common types of two-mast sailboats. It has two masts: a mizzenmast and the mainmast. The mizzenmast is usually much shorter than the mainmast. This makes it an oblique type of a sailboat in the sense that the mainmast is located in the front of the boat while the mizzenmast is located in the rear past or the boat.

The mizzenmast of a yawl is mainly used to increase the helm balance and is located aft of or behind the rudder.

It’s always easy to confuse a yawl with a ketch so it would only make sense to clear up before going any further. They both have two masts with the mainmast at the front while the mizzenmast is smaller. The difference between a ketch and a yawl comes down to the location of the mast. In a yawl, the mizzenmast is behind the rudder post while in a ketch, the mizzenmast if in front of the rudder post.

Again, the mizzenmast of a ketch is nearly as tall as the mainmast and is used to carry a mainsail. Its main function, however, is to drive the sailboat forward and can sufficiently sail the boat, especially in heavier winds. This is very different from the mizzenmast of a yawl, which is only used to increase the helm balance and cannot drive the boat forward. This means that the mizzenmast of a ketch is bigger than the mizzenmast of a yawl. In short, the mizzenmast on a ketch is technically a driving sail while the mizzenmast on a yawl is more of a balancing sail.

A ketch generally has an advantage over a sloop in downwind or in heavy winds. This is because it has a variety of setups than a typical sloop. The mizzenmast gives you a lot of options to depower in heavy winds and find the most perfect amount of canvas to fly. It can also help in stabilizing the sailboat under the power given that the mizzenmast is naturally in an excellent position.

In essence, a ketch has many practical benefits that can be ideal in most situations in the waters. In addition to sailing peacefully on a beam-reach, a ketch is easily manageable and can give you a lot of options in various weather conditions and situations.

When it comes to a two-mast schooner (a schooner can have two or more masts), the foremast is usually smaller than the aft most mast, which is essentially the mainmast. As such, the main characteristic of a schooner is that the masts are almost of the same height but the foremost mast is slightly smaller.

Even though a schooner is easier to sail than say a sloop (one-mast sailboat), it isn’t very fast. This is why most sailors prefer a sloop to a schooner but it’s a sight to behold, especially when under full sail. While a schooner with a square topsail is the most common, there are others with sprit rigs that run diagonally. Schooners with spritsails are not ideal in big seaways because the sprit rig cannot be lowered since it could become unmanageable. On the other hand, the sprit rig is ideal in coastal waters given that the topsail can catch a high up breeze. 

Like the above-mentioned two-mast sailboats, the brig has two masts with the foremost mast squared. The mainmast can be squared, partially squared or triangular. Some brig sailboats have a lateen mainsail on the mainmast. Historically, brigs were used by pirates and were set in motion using oars. Its name is derived from the Italian word “brigantine,” which loosely translates to “pirate.” These types of sailboats were used by pirates the Mediterranean in the 16th century before they became sailboats.

The two most common types of brigs are:

Brigantine – The foremost mast is usually partially squared but the mainmast is triangular.

Hermaphrodite brig – It’s also known as the schooner brig or the half brig. The two masts are partially squared but the mainmast is gaff-rigged and topsail, which technically makes it half schooner.

When it comes to speed and maneuverability, brigs are easy to handle and maneuver and perhaps that’s why they were preferred by pirates. Again, brigs are generally larger than other two-mast sailboats or single-mast sailboats.

There you have it; there are various types of two-mast sailboats, so there’s not a single name that fits all. You can choose any of them as they’ll serve you perfectly, especially in heavy wind conditions.

Bon Voyage!

Related Articles

Daniel Wade

I've personally had thousands of questions about sailing and sailboats over the years. As I learn and experience sailing, and the community, I share the answers that work and make sense to me, here on Life of Sailing.

by this author

Learn About Sailboats

Sailboat Parts

Most Recent

Dufour Sailboats Guide & Common Problems

October 16, 2024

What Does "Sailing By The Lee" Mean?

October 3, 2023

Important Legal Info

Lifeofsailing.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon. This site also participates in other affiliate programs and is compensated for referring traffic and business to these companies.

Similar Posts

The Best Sailing Schools And Programs: Reviews & Ratings

September 26, 2023

Affordable Sailboats You Can Build at Home

September 24, 2024

Best Small Sailboat Ornaments

September 12, 2023

Popular Posts

Best Liveaboard Catamaran Sailboats

December 28, 2023

Can a Novice Sail Around the World?

Elizabeth O'Malley

June 15, 2022

4 Best Electric Outboard Motors

How Long Did It Take The Vikings To Sail To England?

10 Best Sailboat Brands (And Why)

December 20, 2023

7 Best Places To Liveaboard A Sailboat

7 Popular Sailboats with Two Masts (With Pictures & Prices)

Sailboats can come with one, two, or even more masts. You can also have different-sized masts placed on the front, back, or middle of your vessel.

Below, I have listed popular sailboats that have two masts.

Let’s get started!

Table of Contents

Check also: Average sailboat price examples .

Things to Know About Sailboats With Two Masts

When looking for sailboats with two masts, you should know what you are looking for. A Ketch is one type of sailboat with two masts.

Knowing this term can help you to nail down your search when looking for a boat with two masts.

These boats come in many shapes and sizes as well as many different types of designs. Generally, these types of boats have the taller mast being forward and the smaller mast near the aft.

Yawls are also boats that feature two masts.

These also come in multiple types and designs. The difference between the Ketch and the Yawl is that the Yawl has the larger mast in the aft instead of forward. They also have smaller sails and can be easier to handle.

Another type of sailing ship that features two masts is a Brigantine.

This ship has mixed sailing rigs which commonly features squared sails on the front part of the ship and triangular sails on the back of the ship.

These boats are often larger and require more people to handle them.

7 Great Used Boats with Two Masts

There are many benefits to used boats including a lower cost. You can get a larger boat for a lower cost if you choose to buy used.

When looking at used boats, you need to make sure you look at the boat and its features thoroughly to make sure everything is in great working order.

If you do not feel confident that you can properly look over a used vessel, you can even hire a marine inspector to look it over and let you know of any potential issues or needed repairs. You can use this assessment to decide what is worth it, or if the needed repairs fall into the budget.

It is much more common for a used boat to have more than one mast. This is because the newer sailboat models are creating their new designs with just one mast.

One mast ships are easier to handle and manage so new designs are trying to optimize design and ease of sailing.

Below are great used sailboats with two masts which I have arranged by price .

1. 1976 Westerly Center Cockpit Ketch

This 1976 Westerly Center Cockpit Ketch is a small 36-foot long sailboat with two masts. This is a solidly built cruising vessel that features a center cockpit ketch layout.

This boat has a small 38 horsepower engine perfectly fit to navigate its smaller size.

The interior features 1 single berth and 3 double berths all in 3 cabins. This boat also has 2 full heads onboard.

You also have a full galley with a 4 burner stove, refrigerator and freezer, stainless steel sink, and microwave oven.

This boat makes great use of limited space and offers many amenities in a much smaller frame.

Price: $37,000.00

2. 1978 Jeanneau Gin Fizz

The 1978 Jeanneau Gin Fizz is a trusted and popular two-masted design capable of crossing the Atlantic Ocean .

This boat is also very spacious for a boat that is only 38 feet in length. This model also won an award for “security, comfort, ease of handling, and ability to handle varying conditions.”

This particular used model has been well maintained and upgraded over the years.

This boat is great for family cruising, offshore passages, and even racing.

This boat features a 50 horsepower engine to help navigation.

Inside you can find 2 cabins and 1 head. You will be highly comfortable with air conditioning and other interior luxuries.

Price: $46,000.00

3. 1979 Freedom 40

The Freedom 40 is a classically designed centerboard ketch with two masts. This boat is a great sailor loaded for cruising on the wide-open blue water.

This sailboat is 40 feet in length and features accommodations for six people that include a double-v berth, another double berth, and two single berths.

There is also a full head that can be accessed both from the main salon and aft cabin.

This boat was recently painted and features newer interior fabrics, forced air heating, and much more.

You can find a dinette with separate freezer and refrigeration compartments, a stove with an oven and broiler, a double stainless steel sink, plenty of storage, and other interior features.

This boat also comes with an outboard motor with 50 horsepower and a hard bottom inflatable dinghy.

Price: $54,900.00

4. 1977 Puma 38 Ketch

The Puma 38 Ketch is a two-masted sailboat built for racing like the rest of the Puma sailing line. This brand prides itself on speed and maneuverability.

The 1977 Puma 38 is 34 feet in length with a backup diesel engine that can help you get where you need to go as well as docking into a slip. This motor features more horsepower than the average sailboat with 45 horsepower.

Features on this vessel include autopilot, electrical and manual bilge pumps, a full marine head, running hot water, and refrigerator.

This boat is made of fiberglass with teak finishes and looks well kept. You can find this boat in Spain if you are interested in purchasing it.

Price: $66,099.00

5. 1973 Morgan Out Island 41

Originally designed by Charley Morgan, the Morgan Out Island 41 is a center cockpit shoal-draft cruiser that features two masts.

This larger boat is 41 feet 3 inches in length and features many amenities.

This boat is the tri-cabin version and features interior heating, pressurized hot and cold water, a 2 burner gas oven, and a fridge.

This boat also seats up to 7 in the 3 cabins and the saloon. There are also 2 full heads on this vessel.

This boat is even equipped with an inboard motor . Inboard motors are easier when it comes to navigation including backing up, which is generally hard for sailboats to do.

Price: $68,596.00

6. 1970 Hinckley Bermuda 40

This 1970 Hinckley Bermuda 40 is a gorgeous two-masted boat painted with a mixture of desert sand and oyster white on the exterior and features a beautiful and well-kept deck.

This boat has previously had all her systems replaced and upgraded and features a 40 horsepower engine that was new in 2014.

This boat features a mahogany interior and sleeps up to 6 people in 2 cabins. You can also find a 3 burner propane stove with oven, fridge and compressor, new countertops and plenty of storage.

This boat is a stunning and highly upgraded “must-see” at a very reasonable price.

Price: $129,500.00

7. 1995 Amel Super Maramu

A newer model of sailboat is the 1995 Amel Super Maramu sailboat. This sailboat has two masts and is very long at 53 feet.

This boat features an aft deck, steps molded right into the hull, well-protected cockpit an many other features. This boat has a large 76 horsepower engine which is more than the average sailboat is equipped with.

Inside, this boat features 2 cabins and 2 heads with showers. There is also plenty of storage, air conditioning , and electric heaters. There is also a nice salon and galley with a refrigerator, dishwasher, chest freezer, microwave oven, 3 burner stove, and other appliances.

This boat is great for multiple days out on the water and is new and updated. Because of the year, this was manufactured and the features, this boat has a larger price tag than the previous models.

Price: $299,990.00

Final Thoughts:

Sailboats are a great way to enjoy a day out at sea. Most sailboat models come with sleeping arrangements and even a kitchen. This makes them ideal for trips that will take more than a day.

Having multiple masts allows you to harness the power of the wind better and can increase your speed and directional capabilities.

There are many great choices when it comes to boats with two masts, but newer models are starting to steer away from double mast designs. This does not mean that you cannot get a good boat with two masts.

Used boats can be great choices when it comes to purchasing a boat. This is even more true with large, yacht boats such as the ones listed above.

Just make sure when you buy a used sailboat you check that everything is intact and in good working order and if it is not, you have allotted space in the budget to fix what is needed.

Your new double-masted sailboat should provide you with plenty of long-lasting memories and adventures out on the water while you connect with the wind and the sea.

Click to share...

The Ultimate Guide to Sail Types and Rigs (with Pictures)

What's that sail for? Generally, I don't know. So I've come up with a system. I'll explain you everything there is to know about sails and rigs in this article.

What are the different types of sails? Most sailboats have one mainsail and one headsail. Typically, the mainsail is a fore-and-aft bermuda rig (triangular shaped). A jib or genoa is used for the headsail. Most sailors use additional sails for different conditions: the spinnaker (a common downwind sail), gennaker, code zero (for upwind use), and stormsail.

Each sail has its own use. Want to go downwind fast? Use a spinnaker. But you can't just raise any sail and go for it. It's important to understand when (and how) to use each sail. Your rigging also impacts what sails you can use.

On this page:

Different sail types, the sail plan of a bermuda sloop, mainsail designs, headsail options, specialty sails, complete overview of sail uses, mast configurations and rig types.

This article is part 1 of my series on sails and rig types. Part 2 is all about the different types of rigging. If you want to learn to identify every boat you see quickly, make sure to read it. It really explains the different sail plans and types of rigging clearly.

Guide to Understanding Sail Rig Types (with Pictures)

First I'll give you a quick and dirty overview of sails in this list below. Then, I'll walk you through the details of each sail type, and the sail plan, which is the godfather of sail type selection so to speak.

Click here if you just want to scroll through a bunch of pictures .

Here's a list of different models of sails: (Don't worry if you don't yet understand some of the words, I'll explain all of them in a bit)

• Jib - triangular staysail
• Genoa - large jib that overlaps the mainsail
• Spinnaker - large balloon-shaped downwind sail for light airs
• Gennaker - crossover between a Genoa and Spinnaker
• Code Zero or Screecher - upwind spinnaker
• Drifter or reacher - a large, powerful, hanked on genoa, but made from lightweight fabric
• Windseeker - tall, narrow, high-clewed, and lightweight jib
• Trysail - smaller front-and-aft mainsail for heavy weather
• Storm jib - small jib for heavy weather

I have a big table below that explains the sail types and uses in detail .

I know, I know ... this list is kind of messy, so to understand each sail, let's place them in a system.

The first important distinction between sail types is the placement . The mainsail is placed aft of the mast, which simply means behind. The headsail is in front of the mast.

Generally, we have three sorts of sails on our boat:

• Mainsail: The large sail behind the mast which is attached to the mast and boom
• Headsail: The small sail in front of the mast, attached to the mast and forestay (ie. jib or genoa)
• Specialty sails: Any special utility sails, like spinnakers - large, balloon-shaped sails for downwind use

The second important distinction we need to make is the functionality . Specialty sails (just a name I came up with) each have different functionalities and are used for very specific conditions. So they're not always up, but most sailors carry one or more of these sails.

They are mostly attached in front of the headsail, or used as a headsail replacement.

The specialty sails can be divided into three different categories:

• downwind sails - like a spinnaker
• light air or reacher sails - like a code zero
• storm sails

The parts of any sail

Whether large or small, each sail consists roughly of the same elements. For clarity's sake I've took an image of a sail from the world wide webs and added the different part names to it:

• Head: Top of the sail
• Tack: Lower front corner of the sail
• Foot: Bottom of the sail
• Luff: Forward edge of the sail
• Leech: Back edge of the sail
• Clew: Bottom back corner of the sail

So now we speak the same language, let's dive into the real nitty gritty.

Basic sail shapes

Roughly speaking, there are actually just two sail shapes, so that's easy enough. You get to choose from:

• square rigged sails
• fore-and-aft rigged sails

I would definitely recommend fore-and-aft rigged sails. Square shaped sails are pretty outdated. The fore-and-aft rig offers unbeatable maneuverability, so that's what most sailing yachts use nowadays.

Square sails were used on Viking longships and are good at sailing downwind. They run from side to side. However, they're pretty useless upwind.

A fore-and-aft sail runs from the front of the mast to the stern. Fore-and-aft literally means 'in front and behind'. Boats with fore-and-aft rigged sails are better at sailing upwind and maneuvering in general. This type of sail was first used on Arabic boats.

As a beginner sailor I confuse the type of sail with rigging all the time. But I should cut myself some slack, because the rigging and sails on a boat are very closely related. They are all part of the sail plan .

A sail plan is made up of:

• Mast configuration - refers to the number of masts and where they are placed
• Sail type - refers to the sail shape and functionality
• Rig type - refers to the way these sails are set up on your boat

There are dozens of sails and hundreds of possible configurations (or sail plans).

For example, depending on your mast configuration, you can have extra headsails (which then are called staysails).

The shape of the sails depends on the rigging, so they overlap a bit. To keep it simple I'll first go over the different sail types based on the most common rig. I'll go over the other rig types later in the article.

Bermuda Sloop: the most common rig

Most modern small and mid-sized sailboats have a Bermuda sloop configuration . The sloop is one-masted and has two sails, which are front-and-aft rigged. This type of rig is also called a Marconi Rig. The Bermuda rig uses a triangular sail, with just one side of the sail attached to the mast.

The mainsail is in use most of the time. It can be reefed down, making it smaller depending on the wind conditions. It can be reefed down completely, which is more common in heavy weather. (If you didn't know already: reefing is skipper terms for rolling or folding down a sail.)

In very strong winds (above 30 knots), most sailors only use the headsail or switch to a trysail.

The headsail powers your bow, the mainsail powers your stern (rear). By having two sails, you can steer by using only your sails (in theory - it requires experience). In any case, two sails gives you better handling than one, but is still easy to operate.

Let's get to the actual sails. The mainsail is attached behind the mast and to the boom, running to the stern. There are multiple designs, but they actually don't differ that much. So the following list is a bit boring. Feel free to skip it or quickly glance over it.

• Square Top racing mainsail - has a high performance profile thanks to the square top, optional reef points
• Racing mainsail - made for speed, optional reef points
• Cruising mainsail - low-maintenance, easy to use, made to last. Generally have one or multiple reef points.
• Full-Batten Cruising mainsail - cruising mainsail with better shape control. Eliminates flogging. Full-length battens means the sail is reinforced over the entire length. Generally have one or multiple reef points.
• High Roach mainsail - crossover between square top racing and cruising mainsail, used mostly on cats and multihulls. Generally have one or multiple reef points.
• Mast Furling mainsail - sails specially made to roll up inside the mast - very convenient but less control; of sail shape. Have no reef points
• Boom Furling mainsail - sails specially made to roll up inside the boom. Have no reef points.

The headsail is the front sail in a front-and-aft rig. The sail is fixed on a stay (rope, wire or rod) which runs forward to the deck or bowsprit. It's almost always triangular (Dutch fishermen are known to use rectangular headsail). A triangular headsail is also called a jib .

Headsails can be attached in two ways:

• using roller furlings - the sail rolls around the headstay
• hank on - fixed attachment

Types of jibs:

Typically a sloop carries a regular jib as its headsail. It can also use a genoa.

• A jib is a triangular staysail set in front of the mast. It's the same size as the fore-triangle.
• A genoa is a large jib that overlaps the mainsail.

What's the purpose of a jib sail? A jib is used to improve handling and to increase sail area on a sailboat. This helps to increase speed. The jib gives control over the bow (front) of the ship, making it easier to maneuver the ship. The mainsail gives control over the stern of the ship. The jib is the headsail (frontsail) on a front-and-aft rig.

The size of the jib is generally indicated by a number - J1, 2, 3, and so on. The number tells us the attachment point. The order of attachment points may differ per sailmaker, so sometimes J1 is the largest jib (on the longest stay) and sometimes it's the smallest (on the shortest stay). Typically the J1 jib is the largest - and the J3 jib the smallest.

Most jibs are roller furling jibs: this means they are attached to a stay and can be reefed down single-handedly. If you have a roller furling you can reef down the jib to all three positions and don't need to carry different sizes.

Originally called the 'overlapping jib', the leech of the genoa extends aft of the mast. This increases speed in light and moderate winds. A genoa is larger than the total size of the fore-triangle. How large exactly is indicated by a percentage.

• A number 1 genoa is typically 155% (it used to be 180%)
• A number 2 genoa is typically 125-140%

Genoas are typically made from 1.5US/oz polyester spinnaker cloth, or very light laminate.

This is where it gets pretty interesting. You can use all kinds of sails to increase speed, handling, and performance for different weather conditions.

Some rules of thumb:

• Large sails are typically good for downwind use, small sails are good for upwind use.
• Large sails are good for weak winds (light air), small sails are good for strong winds (storms).

Downwind sails

Thanks to the front-and-aft rig sailboats are easier to maneuver, but they catch less wind as well. Downwind sails are used to offset this by using a large sail surface, pulling a sailboat downwind. They can be hanked on when needed and are typically balloon shaped.

Here are the most common downwind sails:

• Big gennaker
• Small gennaker

A free-flying sail that fills up with air, giving it a balloon shape. Spinnakers are generally colorful, which is why they look like kites. This downwind sail has the largest sail area, and it's capable of moving a boat with very light wind. They are amazing to use on trade wind routes, where they can help you make quick progress.

Spinnakers require special rigging. You need a special pole and track on your mast. You attach the sail at three points: in the mast head using a halyard, on a pole, and on a sheet.

The spinnaker is symmetrical, meaning the luff is as long as its leech. It's designed for broad reaching.

Gennaker or cruising spinnaker

The Gennaker is a cross between the genoa and the spinnaker. It has less downwind performance than the spinnaker. It is a bit smaller, making it slower, but also easier to handle - while it remains very capable. The cruising spinnaker is designed for broad reaching.

The gennaker is a smaller, asymmetric spinnaker that's doesn't require a pole or track on the mast. Like the spinnaker, and unlike the genoa, the gennaker is set flying. Asymmetric means its luff is longer than its leech.

You can get big and small gennakers (roughly 75% and 50% the size of a true spinnaker).

Also called ...

• the cruising spinnaker
• cruising chute
• pole-less spinnaker
• SpinDrifter

... it's all the same sail.

Light air sails

There's a bit of overlap between the downwind sails and light air sails. Downwind sails can be used as light air sails, but not all light air sails can be used downwind.

Here are the most common light air sails:

• Spinnaker and gennaker

Drifter reacher

Code zero reacher.

A drifter (also called a reacher) is a lightweight, larger genoa for use in light winds. It's roughly 150-170% the size of a genoa. It's made from very lightweight laminated spinnaker fabric (1.5US/oz).

Thanks to the extra sail area the sail offers better downwind performance than a genoa. It's generally made from lightweight nylon. Thanks to it's genoa characteristics the sail is easier to use than a cruising spinnaker.

The code zero reacher is officially a type of spinnaker, but it looks a lot like a large genoa. And that's exactly what it is: a hybrid cross between the genoa and the asymmetrical spinnaker (gennaker). The code zero however is designed for close reaching, making it much flatter than the spinnaker. It's about twice the size of a non-overlapping jib.

A windseeker is a small, free-flying staysail for super light air. It's tall and thin. It's freestanding, so it's not attached to the headstay. The tack attaches to a deck pad-eye. Use your spinnakers' halyard to raise it and tension the luff.

It's made from nylon or polyester spinnaker cloth (0.75 to 1.5US/oz).

It's designed to guide light air onto the lee side of the main sail, ensuring a more even, smooth flow of air.

Stormsails are stronger than regular sails, and are designed to handle winds of over 45 knots. You carry them to spare the mainsail. Sails

A storm jib is a small triangular staysail for use in heavy weather. If you participate in offshore racing you need a mandatory orange storm jib. It's part of ISAF's requirements.

A trysail is a storm replacement for the mainsail. It's small, triangular, and it uses a permanently attached pennant. This allows it to be set above the gooseneck. It's recommended to have a separate track on your mast for it - you don't want to fiddle around when you actually really need it to be raised ... now.

Why Use Different Sails At All?

You could just get the largest furling genoa and use it on all positions. So why would you actually use different types of sails?

The main answer to that is efficiency . Some situations require other characteristics.

Having a deeply reefed genoa isn't as efficient as having a small J3. The reef creates too much draft in the sail, which increases heeling. A reefed down mainsail in strong winds also increases heeling. So having dedicated (storm) sails is probably a good thing, especially if you're planning more demanding passages or crossings.

But it's not just strong winds, but also light winds that can cause problems. Heavy sails will just flap around like laundry in very light air. So you need more lightweight fabrics to get you moving.

What Are Sails Made Of?

The most used materials for sails nowadays are:

• Dacron - woven polyester
• woven nylon
• laminated fabrics - increasingly popular

Sails used to be made of linen. As you can imagine, this is terrible material on open seas. Sails were rotting due to UV and saltwater. In the 19th century linen was replaced by cotton.

It was only in the 20th century that sails were made from synthetic fibers, which were much stronger and durable. Up until the 1980s most sails were made from Dacron. Nowadays, laminates using yellow aramids, Black Technora, carbon fiber and Spectra yarns are more and more used.

Laminates are as strong as Dacron, but a lot lighter - which matters with sails weighing up to 100 kg (220 pounds).

By the way: we think that Viking sails were made from wool and leather, which is quite impressive if you ask me.

In this section of the article I give you a quick and dirty summary of different sail plans or rig types which will help you to identify boats quickly. But if you want to really understand it clearly, I really recommend you read part 2 of this series, which is all about different rig types.

You can't simply count the number of masts to identify rig type But you can identify any rig type if you know what to look for. We've created an entire system for recognizing rig types. Let us walk you through it. Read all about sail rig types

As I've said earlier, there are two major rig types: square rigged and fore-and-aft. We can divide the fore-and-aft rigs into three groups:

• Bermuda rig (we have talked about this one the whole time) - has a three-sided mainsail
• Gaff rig - has a four-sided mainsail, the head of the mainsail is guided by a gaff
• Lateen rig - has a three-sided mainsail on a long yard

There are roughly four types of boats:

• one masted boats - sloop, cutter
• two masted boats - ketch, schooner, brig
• three masted - barque
• fully rigged or ship rigged - tall ship

Everything with four masts is called a (tall) ship. I think it's outside the scope of this article, but I have written a comprehensive guide to rigging. I'll leave the three and four-masted rigs for now. If you want to know more, I encourage you to read part 2 of this series.

One-masted rigs

Boats with one mast can have either one sail, two sails, or three or more sails.

The 3 most common one-masted rigs are:

• Cat - one mast, one sail
• Sloop - one mast, two sails
• Cutter - one mast, three or more sails

1. Gaff Cat

2. Gaff Sloop

Two-masted rigs

Two-masted boats can have an extra mast in front or behind the main mast. Behind (aft of) the main mast is called a mizzen mast . In front of the main mast is called a foremast .

The 5 most common two-masted rigs are:

• Lugger - two masts (mizzen), with lugsail (cross between gaff rig and lateen rig) on both masts
• Yawl - two masts (mizzen), fore-and-aft rigged on both masts. Main mast much taller than mizzen. Mizzen without mainsail.
• Ketch - two masts (mizzen), fore-and-aft rigged on both masts. Main mast with only slightly smaller mizzen. Mizzen has mainsail.
• Schooner - two masts (foremast), generally gaff rig on both masts. Main mast with only slightly smaller foremast. Sometimes build with three masts, up to seven in the age of sail.
• Brig - two masts (foremast), partially square-rigged. Main mast carries small lateen rigged sail.

4. Schooner

5. Brigantine

This article is part 1 of a series about sails and rig types If you want to read on and learn to identify any sail plans and rig type, we've found a series of questions that will help you do that quickly. Read all about recognizing rig types

Related Questions

What is the difference between a gennaker & spinnaker? Typically, a gennaker is smaller than a spinnaker. Unlike a spinnaker, a gennaker isn't symmetric. It's asymmetric like a genoa. It is however rigged like a spinnaker; it's not attached to the forestay (like a jib or a genoa). It's a downwind sail, and a cross between the genoa and the spinnaker (hence the name).

What is a Yankee sail? A Yankee sail is a jib with a high-cut clew of about 3' above the boom. A higher-clewed jib is good for reaching and is better in high waves, preventing the waves crash into the jibs foot. Yankee jibs are mostly used on traditional sailboats.

How much does a sail weigh? Sails weigh anywhere between 4.5-155 lbs (2-70 kg). The reason is that weight goes up exponentially with size. Small boats carry smaller sails (100 sq. ft.) made from thinner cloth (3.5 oz). Large racing yachts can carry sails of up to 400 sq. ft., made from heavy fabric (14 oz), totaling at 155 lbs (70 kg).

What's the difference between a headsail and a staysail? The headsail is the most forward of the staysails. A boat can only have one headsail, but it can have multiple staysails. Every staysail is attached to a forward running stay. However, not every staysail is located at the bow. A stay can run from the mizzen mast to the main mast as well.

What is a mizzenmast? A mizzenmast is the mast aft of the main mast (behind; at the stern) in a two or three-masted sailing rig. The mizzenmast is shorter than the main mast. It may carry a mainsail, for example with a ketch or lugger. It sometimes doesn't carry a mainsail, for example with a yawl, allowing it to be much shorter.

Special thanks to the following people for letting me use their quality photos: Bill Abbott - True Spinnaker with pole - CC BY-SA 2.0 lotsemann - Volvo Ocean Race Alvimedica and the Code Zero versus SCA and the J1 - CC BY-SA 2.0 Lisa Bat - US Naval Academy Trysail and Storm Jib dry fit - CC BY-SA 2.0 Mike Powell - White gaff cat - CC BY-SA 2.0 Anne Burgess - Lugger The Reaper at Scottish Traditional Boat Festival

Hi, I stumbled upon your page and couldn’t help but notice some mistakes in your description of spinnakers and gennakers. First of all, in the main photo on top of this page the small yacht is sailing a spinnaker, not a gennaker. If you look closely you can see the spinnaker pole standing on the mast, visible between the main and headsail. Further down, the discription of the picture with the two German dinghies is incorrect. They are sailing spinnakers, on a spinnaker pole. In the farthest boat, you can see a small piece of the pole. If needed I can give you the details on the difference between gennakers and spinnakers correctly?

Hi Shawn, I am living in Utrecht I have an old gulf 32 and I am sailing in merkmeer I find your articles very helpful Thanks

Thank you for helping me under stand all the sails there names and what there functions were and how to use them. I am planning to build a trimaran 30’ what would be the best sails to have I plan to be coastal sailing with it. Thank you

Hey Comrade!

Well done with your master piece blogging. Just a small feedback. “The jib gives control over the bow of the ship, making it easier to maneuver the ship. The mainsail gives control over the stern of the ship.” Can you please first tell the different part of a sail boat earlier and then talk about bow and stern later in the paragraph. A reader has no clue on the newly introduced terms. It helps to keep laser focused and not forget main concepts.

Shawn, I am currently reading How to sail around the World” by Hal Roth. Yes, I want to sail around the world. His book is truly grounded in real world experience but like a lot of very knowledgable people discussing their area of expertise, Hal uses a lot of terms that I probably should have known but didn’t, until now. I am now off to read your second article. Thank You for this very enlightening article on Sail types and their uses.

Shawn Buckles

HI CVB, that’s a cool plan. Thanks, I really love to hear that. I’m happy that it was helpful to you and I hope you are of to a great start for your new adventure!

Hi GOWTHAM, thanks for the tip, I sometimes forget I haven’t specified the new term. I’ve added it to the article.

Nice article and video; however, you’re mixing up the spinnaker and the gennaker.

A started out with a question. What distinguishes a brig from a schooner? Which in turn led to follow-up questions: I know there are Bermuda rigs and Latin rig, are there more? Which in turn led to further questions, and further, and further… This site answers them all. Wonderful work. Thank you.

Great post and video! One thing was I was surprised how little you mentioned the Ketch here and not at all in the video or chart, and your sample image is a large ship with many sails. Some may think Ketch’s are uncommon, old fashioned or only for large boats. Actually Ketch’s are quite common for cruisers and live-aboards, especially since they often result in a center cockpit layout which makes for a very nice aft stateroom inside. These are almost exclusively the boats we are looking at, so I was surprised you glossed over them.

Love the article and am finding it quite informative.

While I know it may seem obvious to 99% of your readers, I wish you had defined the terms “upwind” and “downwind.” I’m in the 1% that isn’t sure which one means “with the wind” (or in the direction the wind is blowing) and which one means “against the wind” (or opposite to the way the wind is blowing.)

paul adriaan kleimeer

like in all fields of syntax and terminology the terms are colouual meaning local and then spead as the technology spread so an history lesson gives a floral bouque its colour and in the case of notical terms span culture and history adds an detail that bring reverence to the study simply more memorable.

Hi, I have a small yacht sail which was left in my lock-up over 30 years ago I basically know nothing about sails and wondered if you could spread any light as to the make and use of said sail. Someone said it was probably originally from a Wayfayer wooden yacht but wasn’t sure. Any info would be must appreciated and indeed if would be of any use to your followers? I can provide pics but don’t see how to include them at present

kind regards

Leave a comment

You may also like, 17 sailboat types explained: how to recognize them.

Ever wondered what type of sailboat you're looking at? Identifying sailboats isn't hard, you just have to know what to look for. In this article, I'll help you.

How Much Sailboats Cost On Average (380+ Prices Compared)

Two-Mast Sailboat Types

Numerous sailors have a soft spot for two-mast sailboats, and there really is something unique in two-mast sails, irrespective of whether you are a sailboat enthusiast or just an intrigued passerby.

The two masts are typically the first feature you observe on such a sailboat. The mainmast, or foremast will usually be larger than the rear mast, also known as the mizzenmast.

But aside from being elegant and impressive, a two-mast sailboat provides perfect balance, which can be best obtained by making adjustments to the masts in a variety of ways.

The mizzenmast acts as that shoulder you can rely on as it assists with the sailboat’s stability while it is moving, and it can also function as a propulsion system in certain situations.

So, let’s take a look below at various kinds of two-mast sailboats and their advantages!

What Do You Call A Sailboat With Two Masts?

Several sailboats have two masts (see also ‘ Sailboat Mast: Everything You Need To Know ‘), the four most popular of which we will explore in a bit. In these sailboats, the styles of their masts differ in most instances, but the basic concept stays the same.

All these sailboats come with an extra mast at the rear or the front of the foremast. If that supplemental mast is in front of the foremast, it is called a foremast; if it is behind it, it is called a mizzenmast.

Among the most popular two-mast sailing vessels is the yawl. It is equipped with a mizzenmast and a foremast. Typically, the mizzenmast will be relatively short, particularly when compared to the foremast.

This renders it an angled sailboat, seeing that the foremast is situated at the front of the boat and the mizzenmast is situated at the back. A yawl’s mizzenmast is situated toward the back of the boat steering mechanism and is primarily used to boost helm stability.

It’s very easy to mix up a yawl and a ketch, so it’s best to clear that up before proceeding. They both are two-mast sailboats, with the foremast at the front and the mizzenmast behind it.

The spot of the mast is what distinguishes a ketch from a yawl. The mizzenmast is placed behind the boat steering mechanism post in a yawl and in front of it in a ketch.

A ketch’s mizzenmast is approximately the same height as the foremast, and it is employed to hold the mainsail. Its primary purpose, though, is to propel the boat as well as sail it adequately, especially in stronger wind.

That very function contrasts with a yawl’s mizzenmast, which is only utilized to help with balancing the steering wheel and cannot propel the boat forward.

This indicates that a ketch’s mizzenmast is larger than a yawl’s mizzenmast. In summary, a ketch’s mizzenmast is a moving sail, whereas a yawl’s mizzenmast serves as a balancing one.

In downwind or wind gusts, a ketch is at a favorable position when compared to a sloop. This is due to the fact that it has more setup options than a standard sloop.

The rear mast allows the sailor to adjust in strong winds and choose the most appropriate percentage of canvas to move with.

Provided that the mizzenmast is typically in an ideal position, it may also aid in the stabilization of the sailboat under force.

Essentially, a ketch comes with numerous practical advantages that make it ideal for most scenarios on the water.

A ketch, other than cruising serenely on a beam reach, is completely controllable and can provide a wide range of possibilities in a variety of weather circumstances and situations.

A schooner can even have three masts, but the one with two typically has a fairly small mainmast and a bigger mizzenmast, which in essence becomes the mainmast.

As a result, the main feature of a schooner is that its masts are both tall and with little to no difference, with the rear mast, in some cases, being a bit taller.

A schooner is slower than a sloop, despite being simpler to navigate. That is why so many seafarers choose to sail with a sloop than with a schooner, although it’s still an impressive sight, and even more so when fully sailing.

Even though schooners with square-shaped sail is what most people often get, several other schooners available are equipped with diagonal sprit rigs.

Schooners that have spritsails are unsuitable for large sea routes as, when the sprit rig gets lowered, it becomes impossible to manage. The sprit rig, on the contrary, is perfect in coastal areas because the topsail can hold a high gust of wind.

The brig, same as all the previously mentioned sailing ships, is a two-mast sailboat, with the foremast being of a square shape.

The foremast may come in the shape of a square, part square, or triangle in design. The foremast of certain brigs has a lateen mainsail (see also ‘ The Definition And History Of The Lateen (Triangular) Sail ‘).

These sailboats have been heretofore employed by pirates and launched by oars. Its name originates from the Italian term “brigantine,” which roughly translates to “pirate.” Before becoming sailboats, such kinds of sailboats were employed by pirates in the 1500s.

The two most prevalent brig varieties are:

• Brigantine – The main mast is triangular, while the front mast is partly squared.
• Hermaphrodite brig – This brig is equipped with two slightly squared masts, with the mainmast being gaff-rigged and topsail, something that makes it a half schooner. That is why it is also referred to as the schooner brig or the half brig.

Brigs are simple to operate and navigate in terms of speed and drivability, which may be why pirates favored them, and they are usually bigger than the rest of the two-mast or single-mast sailboats.

The Benefits Of A Two-Masted Sailboat

But why might someone prefer a two-masted sailboat more than a single-masted one?

At first glance, perhaps it will look like a one-masted sloop is easier to control. However, having more masts and a wider range of sails to pick from has its benefits.

A Two-Masted Sailboat Has Greater Sail Area Division

When a sail area is split over a larger number of sails, the area for every sail becomes smaller and easier to navigate.

This is especially useful when moving with fewer passengers on board and in strong weather conditions.

A Two-Masted Sailboat Provides More Rough Weather Choices

If a cruiser encounters higher-than-expected winds, having more sails, and thus more alternatives, can be extremely beneficial.

Most ketch-rigged boats, for instance, can rest nicely in rising winds and waves with only the mizzen being used to hold the boat’s bow facing up into the wind, a practice called “heaving to.”

This tends to mean that the staff does not have to be on deck and can remain safely hidden below since the sail works on its own.

A Two-Masted Sailboat Provides More Sail Balance

Seafarers must be knowledgeable of sail balance if they want to maneuver a boat proficiently.

This entails ensuring that the sails are drawn in such a way that the sailboat can float in a horizontal line without having to utilize the rudder excessively in order to right the route.

A Two-Masted Sailboat Allows For Engine-Free Sailing

If you want the enjoyment of cruising without relying on an engine, or if your engine won’t work, knowing that you have a mizzen sail could be extremely advantageous.

The mizzen can be employed to float smoothly and in perfect control when trying to catch or deciding to leave a mooring ball.

The same is true for anchoring while sailing. This is definitely not an uncommon case scenario; we have all had to do something similar at least once in our lives.

A Two-Masted Sailboat Provides An Anchor Riding Sail

Even as you are sailing across the globe, you will inevitably come across an anchorage that is just not perfectly easy and serene.

The smallest wave that can create some kind of shuddering can make people onboard feel nervous and become dissatisfied with their sailing experience.

A two-mast sailboat will be in an advantageous position in this situation as the mizzen can be lifted and fastened in firmly to counteract the boat’s side-to-side moving.

It may also be counterbalanced by attempting to make use of the wind to direct the boat’s bow into the waves, resulting in a way steadier sailboat and a satisfied crew.

A Two-Masted Sailboat Is Nearly Impossible To Be Completely Dismasted

A two-masted sailboat has an extra benefit: the mizzen, while too small to push the sailboat at high speeds, can most likely get you back safe in case the mainmast breaks or is torn apart in extreme situations.

The Bottom Line

There are dozens of reasons why seafarers chant paeans to these sailboats. Even in windy conditions, you can break down the mainmast and employ the mizzen mast to provide a more aligned and pleasant voyage.

There are different kinds of two-mast sailboats, thus there is no single term that can fit them all.

The only thing that can group them is their two-mast feature, so if you decide to sail in one of them, it is up to your preference to choose which one will take you on your next adventure!

Related Posts:

sdmarina.com is for sale

A premium, short, and brandable .com domain! Ideal for your marina or a marine business. Buy it now on GoDaddy.

What Is A Boat With 2 Masts Called? Everything You Need to Know

When you see a sailboat slicing through the water, it’s the masts and sails that often catch your eye. If you see a boat with two masts and wonder what is a boat with two masts called, the answer isn’t as straightforward as you might think.

The name of a boat with two masts can vary based on the arrangement and size of the masts. Next time you’re checking out these sailboats, you’ll know exactly what you’re looking at. Isn’t it cool to put a name to what you see? Keep an eye on the masts, and you’ll be a pro at spotting the difference in no time!

Key Takeaways

• Yawls and Ketches are the most common types of two-masted sailboats.
• Yawl: Two masts, with the smaller mizzenmast behind the boat’s steering wheel.
• Ketch : Two masts, with the mizzenmast ahead of the steering wheel and smaller than the mainmast but still relatively tall.

What Is A Boat With 2 Masts Called?

If the extra mast is in front of the main mast, it is called a foremast, but if the additional mast is behind the main mast, it is called a mizzen mast.

Let’s review these two-masted sailing boats, starting with the ketch:

Image credit: American Sailing Association

The mizzen mast of a ketch is almost as high as the main mast. The mizzen supports the mainsail. However, its primary function is to propel the sailboat forward, and it can sail the boat, especially in stronger winds.

This is very different from the mizzen mast of a yawl, which serves only to balance the rudder and not to propel the boat forward.

This means that the mizzen mast of a ketch is larger than that of a yawl. In short, the mizzen mast of a ketch is technically a driving sail, while the mizzen mast of a dinghy is more of a balancing sail.

A ketch usually has an advantage over a sloop in downwind or high winds. This is because there is a greater variety of configurations than a typical sloop.

The mizzen mast gives you many options for depowering in strong winds and finding the perfect amount of sail. It can also help stabilize the sailboat under power, as the mizzen mast is in an excellent position.

A ketch has many practical advantages that can be ideal in most situations on the water. A ketch not only sails smoothly on a beam but is also easy to maneuver and gives you many options in different weather conditions and situations.

A yawl is one of the typical two-masted sailing boats. It has two masts: a mizzen mast and the main mast.

The mizzen mast is usually much shorter than the main mast. So, it is a leaning sailboat where the main mast is in the front part of the boat while the mizzen mast is in the back part.

The mizzen mast of a yawl is used to improve the balance of the rudder and is located aft or behind the rudder.

It is easy to confuse a yawl with a ketch. Both have two masts, the main mast forward and the smaller mizzen mast.

The difference between a ketch and a yawl is the position of the mast. In a yawl, the mizzen mast is behind the rudder, while in a ketch, it is in front of the rudder.

Like the two-masted sailing vessels mentioned above, the brig has two masts with a square main mast. The main mast can be square, partially square, or triangular. Some brigs have a battened mainsail on the main mast.

Historically, brigs were used by pirates. Their name derives from the Italian word “brigantine,” which translates to “pirate.” This type of sailing vessel was used by Mediterranean pirates in the 16th century before being converted into sailing ships.

The two common types of brigs:

• Brigantine:  The foremast is usually partially square, while the main mast is triangular.
• Hermaphrodite brigantine:  Also known as a schooner brig or half brig. The two masts are partially square, but the main mast is a gull and topsail, making it a half schooner.

In terms of speed and maneuverability, brigs are easy to handle and maneuver, which is why they were favored by pirates

Again, brigs tend to be larger than other two-masted or single-masted sailing vessels.

4. Schooner

In a two-masted schooner (a schooner can have two or more masts), the bow mast is usually smaller than the stern mast, which is the main mast.

Therefore, the main characteristic of a schooner is that the masts are about the same height, but the foremast is slightly smaller.

While a schooner is easier to sail than a sloop or a single-masted sailboat, it is not very fast. For this reason, most sailors prefer a sloop to a schooner, but it is a beautiful sight, especially when sailing under full sail.

Although the schooner with a square topsail is the most common, there are also vessels with diagonally set spritsails.

Schooners with spritsails are not ideal in the larger seaways because the spritsail rig cannot be lowered, or it will become unmaneuverable.

On the other hand, the spritsail rig is ideal for coastal waters because the topsail can take a strong breeze.

Popular Two-Masted Sailboat Models

When you’re looking at two-masted sailboats, you’ll see that there are a few models that stand out from the rest. Each has its own charm and is known for certain features.

Hinckley Bermuda 40

This classic beauty is all about elegance on the water. Since the 1960s, sailors have loved its smooth sailing and comfy inside. Its two masts, including a shorter mizzenmast at the back, make it a yawl and a real eye-catcher at sea.

1976 Westerly Center Cockpit Ketch

This is for those who want a sturdy sail around. It’s a smaller sailboat at 36 feet, but don’t let that fool you. This ketch is well-built and comes with a center cockpit design. Plus, it has a 38 horsepower engine to help you steer through quieter waters.

Nicholson 38

A solid choice for ocean voyaging, the Nicholson 38 has earned its stripes among sailors. It’s one of those boats that balance size and handling, making your sailing both comfy and thrilling.

Bayfield 40

Sleek and ready for long trips, the Bayfield 40 has a dedicated following. It’s got the room you need for those longer adventures and sails that catch the wind just right.

Amel Super Maramu

A favorite for those who eat, sleep, and breathe sailing. It’s built to face the ocean’s moods and keep you safe and sound.

What About Performance and Handling?

When you’re steering a two-masted boat, a few things become really important: how it balances, how it zips through different breezes, and the kind of sharp turns you can pull off.

Balance and Stability

Your boat’s balance and stability depend a lot on how the masts are set up. If your mainmast and mizzenmast are aligned just right, you’ll feel the boat sit pretty steady on the water.

It’s like a seesaw. Get it balanced and your ride’s going to be smooth.

Sailing in Different Wind Conditions

Different winds? No problem. The two masts give you more options to set your sails.

When the wind’s blowing like crazy, you can adjust the sails so you’re not overpowered. And on those lazy breezes, you can catch just enough wind to keep gliding.

Speed and Maneuverability

Want to go fast? That second mast can help, especially when you want to zip around quickly. It helps you turn on a dime and keeps things spry.

But remember, your crew needs to be on their toes, because handling all those sails takes skill and a keen eye.

• How To Sail From California To Hawaii?
• How Long Does It Take To Sail Across The Atlantic?